Siege Overland

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Ultimate style and class; the Sahara Style Flares. 

NOTE: flares are now available for pre-order, order now for delivery in FEB 2025.

Sahara’s traditionally came with fibreglass flares; they gave them a stronger, thicker and even ‘stauncher’ look 😤

It’s hard to track down a good set, some that fits, bolts up and is new and free of damage.

Well, Mick at FRP flares was asked to help a few mates replace their cracked Sahara flares and he came up with these Sahara style flares for those who were after the awesome look 👀😍

FRP Flares, are the BEST aftermarket flares available for 60 Series Landcruisers.

These flares come as a full set, and are supplied in a black or white gelcoat finish, allowing you to paint them to match or contrast your current paintwork 🎨

FRP recommend priming and painting for a good quality and uv resistant finish.  

They're easy to paint and there's no special treatment required, simply sand, prime, sand and paint as you would any panel on the vehicle ✅

Due to the age of the moulds some refinishing may be required, but not much at all 👌🏽

When installing, the top edge of the flares get covered by the rubber seals, underside is a hollow fibreglass.

As you can see in the photos these flares finish at the bottom of the guards so no need for genuine mudflaps.  

FRP flares are screwed to the underlip of the guards, allowing the most cost effective and more importantly the strongest fit possible unlike double sided tape, avoiding fragile and intrusive fitment.

Screws not  included – as a guide 8 gauge 20mm self-drilling button heads, may be most appropriate.

Door flares are supplied with a fibreglass bracket which is screwed to the door then the door flare is screwed to the bracket, this means your flares will never fall off. 

PLEASE NOTE: FRP's OEM Replacement Flares may not bolt directly into existing holes due to manufacturing variations between vehicles.This product is made to order and is NON-RETURNABLE and NON-REFUNDABLE

Some things to know before purchasing:

• FRP state that these DO NOT replace genuine Sahara flares but act as an alternative 🤙🏽
• These flares should be installed by a professional 👨🏽‍🔧
• Shipping is expensive, we apologise! We are trying to find a more economical option but come up short, due to the size of these. If you want to pick these up from Brisbane, Australia please let us know. This is possible 📦
• Although it is possible to install them yourself; we will not warrant, guarantee or grant the return any fibreglass, FRP or Flares products that are installed incorrectly and/or not installed by a professional 🚫
• When purchasing these flares you accept all of these conditions, as well as our terms of service, found below.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Fresh nuts and bolts, there is nothing better! Well, almost 😎

If you have seized, rusty bolts on your 60 series (there is a 95% chance of this), then it is likely you could use this kit ✔️

There is something extremely satisfying in replacing old tired bolts with some freshly zinc plated nuts and bolts 😍

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and yellow zinc coated, to help prevent bolt shearing and save you time. This kit has saved us many times on our own 60, you won't regret this purchase.

Each Kit Contains:

• 55 - M5 Serrated Nut, 8mm Head.
• 150 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 30 - M10 Serrated Nut, 14mm Head.
• 30 - M6.3 x 19mm M10 Hex Head Self Tapper.
• 30 - M5 x 22mm Panel Bolt, 8mm Head, 18mm Washer.
• 75 - M6 x 16mm Panel Bolt M10 Head.
• 30 - M6 x 20mm Panel Bolt M10 Head with 18mm Washer.
• 30 - M6 x 25 Panel Bolt, 10mm Head
• 25 - M8 x 25mm Panel Bolt, 13mm Head
• 25 - M10 x 30mm Panel Bolt, 14mm Head

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Welcome to performance 👑

For years we searched for an intercooler that worked with our HJ61 / 12HT; we wanted something that fit, something of high quality and finally something that was large enough to make a difference on EGT's and IAT's.

We, like you, wanted:

• 💨 Performance
• ⚡️ Quality
• 🔩 Fitment
• 👌🏽 Reliability
• 📞 Manufacturer support

Then, we came across the PDI intercooler from Brian at Performance Diesel Intercoolers in W.A, Australia 🇦🇺

After speaking with Brian, understanding the size of this intercooler, and its design to enable fitment into the HJ61 Landcruiser, as well as it's specs and quality we knew we had to have it 🎁

Not only that, it looked bass ass 😎

If you've got a 12HT or a 2HT, usually you're keen for a little more power, more torque and better performance. 💪🏽

How do we achieve that with these old but brilliant motors? Simple; boost and fuel, > BUT this means higher EGT's and thus higher IAT's; which means hotter engine, rings going bad, overheating, head warping etc etc. 🔥😢

If you have gone through the trauma of any of the above on your beloved 12HT/2H motor then you're understanding how important it is to AVOID this at all costs 👎🏽

Because this means: 

• Getting the engine built; but then there's the cost, what if the builder isn't good and/or make an error, what about their warranty, what if the build cost blows out 💸
• Building the engine yourself; means needing to find space (mum's garage may not fit a small truck engine), finding the time; will it be one of the 50% complete projects for 3 years? you're thinking : "I hate those, my 60 is already one of those!" ⏳

If you're wanting more power, then this is for you; it means boost, cooler EGT's and lower IAT's, it means peace of mind 😌 and motivates you to get your diesel tuned (properly on a dyno 🙄), it means better trips and it looks mean 😈

* Please note, if utilising a custom set-up piping may not fit your set-up. Please let us know your requirements the closest possible will be supplied. This kit is for a 12HT set-up only, whilst we do our best to accomodate a 2H custom set-up, the responsibility of fitment it up to the customer.  

From PDI:

The PDI Landcruiser 60 series HJ61 HJ60 Front mount intercooler is designed to fit on both the round headlight and the twin square light model. It sits further back than all other designs we have seen as it has recessed areas in the end tanks for the condenser fittings and piping.

The core is 545 x 300 x 65mm.

Pipes are stainless steel and is supplied with a stainless flange onto the intake manifold, which does a 180deg bend under the air supply pipe.

Plus, it looks awesome!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

The PDI brake booster is a significant upgrade (50%) to the 60 series, which had a single diaphragm unit. It will fit on auto models and manual with the standard clutch master cylinder, but not if you have the vacuum assist on the clutch master cylinder (due to interference).

If you have the vac assisted clutch booster, you can change it out for a non assisted clutch master, but this will require cutting and re-flaring of the hydraulic line for the clutch. Considering the improvements in clutch design, a new clutch will probably negate the need for vacuum assist and this will allow for the PDI brake booster to be installed.

Braking upgrades should be done in conjunction with power increases and we have found the biggest improvement can be achieved with this mod.

Our PDI dual diaphragm brake boosters have been ADR tested and proved to pass all tests. Our design allows us to exceed the standard brake specifications for those with:

• increased weight (both GVM and GCM).

• larger wheel diameter

Following installation and adjustment of the rear brake bias the braking distance at 80kph dropped from 26m to 16m. Very quickly we found we could do turning and stopping maneuvers that would have be both crazy and impossible before. This is great for a powered up cruiser and potentially life saving if you have increased your weights, fitted larger tyres or are towing. Many will say “the brakes are fine” but when asked if the pedal goes hard, before full braking can be achieved, they remember how scary that can be.

With a PDI brake booster less than 50kg push would be required for full braking - this is a significant improvement that will be noticed.

We recommend these be installed with braided brake lines as line pressure will be increased and the standard lines may be compromised if still original. This is both due to age and the potential for damage as they are fitted to a 4WD. Installing braided lines will also give a better result as factory flexible lines bulge and reduce effective application of the pedal.

Note: If you have air in your system, which can be very very difficult to bleed out, the larger booster will make this more apparent, due to extra force that can be applied.

These boosters are impressive, and we are sure every cruiser owner would install after driving a cruiser fitted with one of these boosters.

We recommend these be installed with braided brake lines as line pressure will be increased and the standard lines may be compromised if still original. This is both due to age and the potential for damage as they are fitted to a 4WD. Installing braided lines will also give a better result as factory flexible lines bulge and reduce effective application of the pedal.

-

The only fitting issue is for those with rear air con or ice box console where the alloy pressure lines are routed close to the brake booster and will result in interference such that our larger boosters can’t be fitted.

Please do your research before purchasing and attempting an install. For those fitting to petrol models we suggest and additional vacuum reservoir be added to ensure the booster is able to provide full assist for a period after the engine is turned off or if being driven enthusiastically where vacuum build up is limited.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Pre-Order a Safari Snorkel kit for your 60 series landcruiser today! Lead time can be up to 2-3 weeks (approximately, depending on stock).

The SS60HF Safari Snorkel suitable for Toyota 60, 61 & 62 Series Landcruiser 4x4 is designed to deliver a huge volume of the coolest and cleanest air possible into the stock air cleaner assembly of 01/1980 - 12/1989 All Engines.

With the huge air flow demands of each engine in the Toyota 01/1980 - 12/1989 All Engines 60, 61 & 62 Series Landcruiser, Safari took the decision to design a snorkel system that raised the air intake to prevent ingesting harmful elements to the vehicles air cleaner.

Huge air flow is but one aspect of the ultimate in snorkel design. The Safari snorkel air ram is designed to perform two very important roles. The most obvious is to funnel cool clean air into the snorkel body - but just as importantly, the Safari air ram acts as a highly efficient water separator to remove rain water from the incoming air stream - thus ensuring safe engine operation through even the most torrential tropical storms.

The genuine Safari Snorkel suitable for Toyota 60, 61 & 62 Series Landcruiser 4x4 Snorkel body and air ram is manufactured to the highest standards in durable, UV stable, cross linked polyethylene material. In addition, the substantial material wall thickness delivers huge physical strength to ensure that the snorkel breezes through the toughest off-road conditions on the planet.

Safari Snorkel suitable for Toyota 60, 61 & 62 Series Landcruiser 4x4 Kit - Parts List

Safari Snorkel suitable for Toyota 60, 61 & 62 Series Landcruiser 4WD Snorkel for 01/1980 - 12/1989 All Engine Models - Part Number SS60HF

SAFARI 4X4 INSTALLATION GUIDE FOR 60, 61 & 62 SERIES LANDCRUISER

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service.