HJ61

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

ONCE SOLD OUT, PRE-ORDER FOR JANUARY 2024 ARRIVAL!

Fresh nuts and bolts, there is nothing better! Well, almost 😎

If you have seized, rusty bolts on your 60 series (there is a 95% chance of this), then it is likely you could use this kit ✔️

There is something extremely satisfying in replacing old tired bolts with some freshly zinc plated nuts and bolts 😍

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and yellow zinc coated, to help prevent bolt shearing and save you time. This kit has saved us many times on our own 60, you won't regret this purchase.

Each Kit Contains:

• 55 - M5 Serrated Nut, 8mm Head.
• 150 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 30 - M10 Serrated Nut, 14mm Head.
• 30 - M6.3 x 19mm M10 Hex Head Self Tapper.
• 30 - M5 x 22mm Panel Bolt, 8mm Head, 18mm Washer.
• 75 - M6 x 16mm Panel Bolt M10 Head.
• 30 - M6 x 20mm Panel Bolt M10 Head with 18mm Washer.
• 30 - M6 x 25 Panel Bolt, 10mm Head
• 25 - M8 x 25mm Panel Bolt, 13mm Head
• 25 - M10 x 30mm Panel Bolt, 14mm Head

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Ultimate style and class; the Sahara Style Falres. 

NOTE: flares are made-to-order, manufacturing lead time can be up to 4 weeks, we appreciate your patience!

Sahara’s traditionally came with fibreglass flares; they gave them a stronger, thicker and even ‘stauncher’ look 😤

It’s hard to track down a good set, some that fits, bolts up and is new and free of damage.

Well, Mick at FRP flares was asked to help a few mates replace their cracked Sahara flares and he came up with these Sahara style flares for those who were after the awesome look 👀😍

 FRP Flares, are the BEST aftermarket flares available for 60 Series Landcruisers.

These flares come as a full set, and are supplied in a black or white gelcoat finish, allowing you to paint them to match or contrast your current paintwork 🎨

FRP recommend priming and painting for a good quality and uv resistant finish.  

They're easy to paint and there's no special treatment required, simply sand, prime, sand and paint as you would any panel on the vehicle ✅

Due to the age of the moulds some refinishing may be required, but not much at all 👌🏽

When installing, the top edge of the flares get covered by the rubber seals, underside is a hollow fibreglass.

As you can see in the photos these flares finish at the bottom of the guards so no need for genuine mudflaps.  

FRP flares are screwed to the underlip of the guards, allowing the most cost effective and more importantly the strongest fit possible unlike double sided tape, avoiding fragile and intrusive fitment.

Screws not  included – as a guide 8 gauge 20mm self-drilling button heads, may be most appropriate.

Door flares are supplied with a fibreglass bracket which is screwed to the door then the door flare is screwed to the bracket, this means your flares will never fall off. 

Some things to know before purchasing:

• FRP state that these DO NOT replace genuine Sahara flares but act as an alternative 🤙🏽
• These flares should be installed by a professional 👨🏽‍🔧
• Shipping is expensive, we apologise! We are trying to find a more economical option but come up short, due to the size of these. If you want to pick these up from Brisbane, Australia please let us know. This is possible 📦
• Although it is possible to install them yourself; we will not warrant, guarantee or grant the return any fibreglass, FRP or Flares products that are installed incorrectly and/or not installed by a professional 🚫
• When purchasing these flares you accept all of these conditions, as well as our terms of service, found below.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

PRE–SALE OPEN NOW! 🏷

Order now for a September-October 2023 (approx.) delivery.

Welcome to brighter, nicer, clearer taillights 🚦🚦

Ever turn to look back at your 60 and find the taillights just a little too dull? 

A little less bright than ideal?

Have you replaced the bulbs and found no difference between the tail and stop lights? Scared someone will run up your backside when you brake?
🚗💥🚙

No, thanks!

So, we worked with the folks at Digitails to bring these down to Australia. And we are stoked with ours. 

The kit is handmade in the USA and is a high-quality replacement for your current incandescent bulbs 💎

Kit Includes two amber and two red panels, which plug directly into your bulb ports 📦

From Digitails:

"Our kits are safer and brighter than standard factory lights or other LED kits because our light panels contain high-intensity wide-angled LEDs strategically positioned to maximise light output and fully optimise your lenses.

EASY INSTALLATION & PRECISION FIT:

Our LED lights have been custom-engineered kits to fit your housing precisely rather than using generic light panels. Our care in design gives you easy installation and exceptional appearance.

Our pigtail kits complete everything needed to replace your old standard bulbs with high-quality LED lighting; clear instructions are included.

DURABLE & LONG-LASTING: 

There is nothing like DigiTails LED lights on the street, making this one of the most satisfying upgrades. "

Details

• Replaces Brake/Running light bulb with an LED panel that emits RED light.
• Replaces Turn Signal light bulb with an LED panel that emits AMBER light.
• Mounting brackets included
• The kit is 100% plug in
• PLEASE NOTE: THIS KIT IS NON-SEQUENTIAL.
• Reverse lights NOT included
• Resistors NOT included

For more information, please refer to our Terms of Service. By purchasing from our site, you acknowledge that you have read and agree to our Terms of Service. 

Welcome to storage.. level 1200, unlocked 🔓🧳

The Huracan Tailgate storage mod is a must do; if you're thinking about it... I get it 🤔

Why bother? 🥱

Let me tell you some problems this WILL solve for you 👇🏽

• Organisation 🗃
• Storage 🧰
• Travelling efficiency 🚙
• Strong 💪🏽
• Use as a bench 🍳
• Easy install, under 45mins ✅

If you travel in your 60, and you have a tailgate, you're already winning in our opinion, but once you install one of these bad boys; it is a game changer ⛳️

It means that you can store recovery, cleaning, tool, tyre changing or whatever other gear your feel necessary all in one spot.

The kit comes with close cell foam for sound and panel insulation 🤫 🔇; so nothing needs to be sitting directly on your tailgate panel (on the inside), and potentially harming the panel, like you and all us have been doing on the inside rear quarter panels 😩

The installation is super simple, requiring a grinder, sockets and a screw driver you simply mark our the template included trim out the section of tailgate and utilise the existing trimming holes to bolt the storage mod to 👩🏽‍🔧

From Huracan Fabrication:
"This precision laser cut steel modification plate allows you to turn your tailgate into a locked compartment within your car.

You can use the space to store recovery gear, spare parts or anything else that will fit and you want to keep secure. This is a DIY kit and requires you to trim away some of the metal in the tailgate. To assist with this, we provide step by step easy to follow instructions and a handy template to show where the cuts are required. This can be performed with tin snips, a jigsaw or an angle grinder.

By default, the kit will be painted black and ship with all mounting hardware required such as nuts and bolts for mounting, hinge and associated screws as well as the heavy duty low profile locks. Sound deadening foam to stick inside your tailgate which prevents damage to the steel and eliminates rattles is also included. Please allow up to one week handling time for your kit to be assembled, packed and picked up by our couriers."

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Welcome to performance 👑

For years we searched for an intercooler that worked with our HJ61 / 12HT; we wanted something that fit, something of high quality and finally something that was large enough to make a difference on EGT's and IAT's.

We, like you, wanted:

• 💨 Performance
• ⚡️ Quality
• 🔩 Fitment
• 👌🏽 Reliability
• 📞 Manufacturer support

Then, we came across the PDI intercooler from Brian at Performance Diesel Intercoolers in W.A, Australia 🇦🇺

After speaking with Brian, understanding the size of this intercooler, and its design to enable fitment into the HJ61 Landcruiser, as well as it's specs and quality we knew we had to have it 🎁

Not only that, it looked bass ass 😎

If you've got a 12HT or a 2HT, usually you're keen for a little more power, more torque and better performance. 💪🏽

How do we achieve that with these old but brilliant motors? Simple; boost and fuel, > BUT this means higher EGT's and thus higher IAT's; which means hotter engine, rings going bad, overheating, head warping etc etc. 🔥😢

If you have gone through the trauma of any of the above on your beloved 12HT/2H motor then you're understanding how important it is to AVOID this at all costs 👎🏽

Because this means: 

• Getting the engine built; but then there's the cost, what if the builder isn't good and/or make an error, what about their warranty, what if the build cost blows out 💸
• Building the engine yourself; means needing to find space (mum's garage may not fit a small truck engine), finding the time; will it be one of the 50% complete projects for 3 years? you're thinking : "I hate those, my 60 is already one of those!" ⏳

If you're wanting more power, then this is for you; it means boost, cooler EGT's and lower IAT's, it means peace of mind 😌 and motivates you to get your diesel tuned (properly on a dyno 🙄), it means better trips and it looks mean 😈

* Please note, if utilising a custom set-up piping may not fit your set-up. Please let us know your requirements the closest possible will be supplied. This kit is for a 12HT set-up only, whilst we do our best to accomodate a 2H custom set-up, the responsibility of fitment it up to the customer.  

From PDI:

The PDI Landcruiser 60 series HJ61 HJ60 Front mount intercooler is designed to fit on both the round headlight and the twin square light model. It sits further back than all other designs we have seen as it has recessed areas in the end tanks for the condenser fittings and piping.

The core is 545 x 300 x 65mm.

Pipes are stainless steel and is supplied with a stainless flange onto the intake manifold, which does a 180deg bend under the air supply pipe.

Plus, it looks awesome!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

 Is your 60 Series still wearing it's original carpet? Chances are very likely, yes it is 👎🏽

It most likely still has dog hair in there from the previous 2x owners, Maccas chips from that late night last year along with some other 'memories embedded' in it 🍟🐶

Definitely, time to replace 🔄

Your 60 Series isn't a new car, but we know there's been a few times when you've hopped in and thought "geez I wish this interior felt cleaner, newer, fresher" 😩

*Please note that wheel arch covers are not included in the rear for this set of carpet for HJ61 and FJ62

This is the first step to a fresh interior... 👄

What problems will this solve?

• Affordable interior refreshen 🍃
• Easy enough self-install; less than half a day 🪛
• Change or refresh the faded old colour 🧼
• Choose a new loop style, or retain the original style 🤌🏽

🔧 Installation, our thoughts? 🤔

Pretty simple install, our process looked like this:

• Throw down a canvas sheet 
• Remove the front seats and centre console
• Remove the rear seats
• Pull out the carpet
• Lay the old carpet down; mark out the old holes on the back of the new carpet, only slice these holes (don't fully cut them out)
• Do sound deadening removal and replace with Car Builders wagon pack (if up to it)
• Lay in your new carpet
• Begin cutting in (very carefully) your handbrake, shifter and seat holes
• Trim off the excess sides of the new carpet (overhanging doors etc.)
• Re-install seats
• Sit back and enjoy your work 👀🍺

Important details:

• 📦 This carpet is made to order; please allow 7-12 working days for your carpet to be shipped, although we aim for 3-4 working days before shipment; you accept that this will take up to 10 business days to make and send + shipping times
• 📑 Please note this carpet will suit; HJ60, HJ61, FJ60, FJ62. These really work well for HJ61s and FJ62s
• 💺 This carpet does cater to (although you will need to mark out and cut out) an under seat heater on the driver's side for HJ61's and FJ62's
• ✂️ Holes are not cut into these carpets; you will need to mark out and cut your own seat, heater, handbrake and shifter holes
• 👉🏽 Whilst these carpets are as close as can be to original; there is some age in the moulds and they may change over time, your floor pan may be slightly varied, or the carpet may take time to get to shape; please allow for this, carpets are made to order you accept all of these conditions when ordering this carpet
• Please note that wheel arch covers are NOT included with this carpet for the rear and must be ordered separately

A note from our supplier: 

Loop Pile - This carpet is constructed using top-quality spun Acrylic yarn and is tufted on a 5/32" gauge tufting machine at 600 grams per square meter.
The carpet is produced in one-meter-wide rolls which are backed with Polyethylene which enables it to be moulded to the contours of an automotive floor pan.
As its name suggests loop pile carpet is made up using many small loops of yarn and is most commonly used in vehicles from the 1960's up until the mid 1980's.

Classic Loop - Our strongest and most durable carpet material. Manufactured by us using the original 80% Rayon and 20% Nylon yarn, it is an exact reproduction of the carpet used by the car makers during 1960’s to 1970’s, including the 60 Series Landcruiser, other types that used this were HK-HG Holden, XT-XY Falcon, Valiant Charger and many other models. It is available in most original colours including black, saddle (Ford), Chev + GMH blue, VH Commodore (Brock), Burgundy along with many other colours and is suitable for all makes and models including present day vehicles.

Please note our carpet comes with NO holes cut in it. Free fitting instructions:

1 - open your parcel, make sure you have everything you ordered
2 - Lay out your new carpet and pop moulded contours back into place if applicable
3 - Remove door sill plates, kick panels, front seats and rear seat base
4 - Remove centre console (where applicable), seat belt bolts and any other trims retaining old carpet
5 - Remove old carpet, keep it do not discard it yet. Remove old underfelt taking note of where it was. Vacuum or sweep the floor clean. Place the old carpet over your new moulded carpet. Using the old carpet as a template, mark any holes or additional cut outs on the new carpet with chalk. Do not cut yet. 
6 - If removing underfelt only, lay it in the same area as you removed it from. 
7 - Starting with the rear carpet, place your new carpet in the vehicle by entering it on the tunnel and working towards the sides.
8 - Now repeat this with the front carpet matching the contours of the carpet with the floor
9 - You may need to cut some of the holes you marked out earlier (gearstick, console brackets, etc.)
10 - After confirming the proper fit, cut the required holes as you fit the carpet to the vehicle
11 - depending on your particular model of vehicle it may be necessary to trim the excess carpet from the sides as most carpets are left slightly wider in case the carpet has been fitted slightly off centre.
12 - replace rear seat base, seat belt bolts, centre console, front seat bolts, kick panels, door sill plates and any other trims your removed earlier.

Please note the colour reproduction of these samples will vary dependant on the viewers graphics/monitor settings. Knox Auto Carpets have no control over these settings and would advise the customer to always email team@siegeoverland.com to discuss their requirements if they have any doubts regarding the correct colour for their vehicle.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

This kit has been meticulously reproduced and professionally printed with attention to detail. Custom colours available at additional cost, contact for more information. Our stripes are "Application Ready", easy-to-install and professionally manufactured from the highest quality Avery vinyls with clear laminate to ensure years of trouble-free use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Touge Nation Money-Back Satisfaction Guarantee!

 Please note: all 60 series body stripe kits from Touge Nation are made-to-order, and kits can take up to 2-3 weeks before being dispatched for delivery.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Due to significant demand and covid impacts, we are unfortunately posting out 1–2 weeks after purchase direct from our supplier. 

Control sound and heat in your truck ready for touring. This pack contains enough insulation to cover 4x4 wagons such as Nissan Patrols and Toyota Land Cruisers

STANDARD PACK

•  Pack 1 comes with Waterproof Carpet underlay - a peel and stick closed cell foam that you stick on the Sound Deadener. 

The 4x4 Wagon Floor pan pack includes:
SKU: 4X4_WGN_1  (approx 30kg)
3 Boxes (5.4 sq/m) of Stage 1 Sound Deadener -  Install on your floor, firewall, inner 1/4 panels, rear wheel arches
2 Boxes (3.6 sq/m) Water Proof Carpet Underlay -  Light weight, closed cell, peel and stick foam. At 10mm the waterproof underlay will replicate your factory underlay, reduce heat transfer and will cover your floor pan and rear firewall.
1 Sheet (1.5 sq/m) Mass Noise Liner - 1 x sheet at 1m x 1.5m,  2 in 1 closed cell thermal water proof underlay with the addition of a heavy weight mass loaded vinyl. This material is a dense sound transmission barrier typically used in luxury vehicles. The MNL is also removable and efficient to install. Install in rear cargo area direct to sheet metal as a sound blanket. DO NOT PUT SOUND DEADENER UNDERNEATH THIS. 
1 x Install kit - Application Roller, Utility Knife and Aluminium Foil Tape

PREMIUM PACKS

Please note that pre-cut floors will dispatch within 2-3 business days.

• Pack 2, 3 and 4 come with Mass Noise Liner Lite - a premium non stick underlay, is closed cell foam with a 2mm thick mass loaded vinyl layer on top. This is waterproof as well, and utilising the vinyl layer as a sound blanket it blocks more sound than Waterproof Underlay. 

The 4x4 Wagon Premium Floor pan pack includes:
Pack 2 (approx 45kg)
3 Boxes (5.4 sq/m) of Stage 1 Sound Deadener -  Install on your floor, firewall, inner 1/4 panels and rear wheel arches.
2.5 Sheets (3.8 sq/m)  Mass Noise Liner Lite- 2 in 1 closed cell thermal water proof underlay with the addition of a heavy weight mass loaded vinyl, install in carpet area up to the rear cargo area. Note carpet gets installed directly ontop of this product.
1 Sheet (1.5 sq/m)  Mass Noise Liner - 2 in 1 closed cell thermal water proof underlay with the addition of a heavy weight mass loaded vinyl install in cargo area. DO NOT PUT SOUND DEADENER UNDERNEATH THIS. 
1 x Install kit - Application Roller, Utility Knife and Aluminium Foil Tape

The 4x4 Wagon Premium Floor Pan & Doors Pack includes:
Pack 3 (approx 55kg)
4 Boxes (7.2 sq/m) of Stage 1 Sound Deadener -  Install on your floor, firewall, inner 1/4 panels, rear wheel arches and door skins.
2.5 Sheets (3.8 sq/m)  Mass Noise Liner Lite - 2 in 1 closed cell thermal water proof underlay with the addition of a heavy weight mass loaded vinyl, install in carpet area up to the rear cargo area. Note carpet gets installed directly ontop of this product.
1 Sheet (1.5 sq/m)   Mass Noise Liner - 2 in 1 closed cell thermal water proof underlay with the addition of a heavy weight mass loaded vinyl install in cargo area. DO NOT PUT SOUND DEADENER UNDERNEATH THIS. 
1 x Install kit - Application Roller, Utility Knife and Aluminium Foil Tape

Full Kit - The 4x4 Wagon Premium Floor Pan, Doors & Roof Pack includes:
Pack 4 (approx 60kg)
5 Boxes (9.0 sq/m) Stage 1 Sound Deadener -  Install on your floor, firewall, inner 1/4 panels, rear wheel arches, doors and roof
2.5 Sheets (3.8 sq/m)  Mass Noise Liner Lite - 2 in 1 closed cell thermal water proof underlay with the addition of a heavy weight mass loaded vinyl, install in carpet area up to the rear cargo area. Note carpet gets installed directly ontop of this product.
1 Sheet (1.5 sq/m)   Mass Noise Liner - 2 in 1 closed cell thermal water proof underlay with the addition of a heavy weight mass loaded vinyl install in cargo area. DO NOT PUT SOUND DEADENER UNDERNEATH THIS. 
3 Sheets (3 sq/m) Insul-Layer - Closed cell peel and stick foam to reduce noise and heat entering and exiting your roof skin.
1 x Install kit - Application Roller, Utility Knife and Aluminium Foil Tape

These are our famous 7 Inch LED Headlights, featuring impressive range, good spread, colourful halos and are indestructible. These draw less power than your regular halogen / HID globes too, and are ADR compliant, meaning they’re legal in every state. This is one pair of lights.

These lights come with a pair of CANBUS Load Modules to make the lights compatible with your Toyota.

These are 7″ round headlights and they fit all 7″ round applications. We have sold thousands and we are yet to have a car with 7″ lights they don’t fit. They are to suit Australian left side of road and are legal in all states. In fact they have ADR cert stamped on the lens and come with an ADR reference sheet.

JTX LED lights are made by us here in Melbourne. We carry all the components to make up all colour combinations. We make them up and send next day or even same day if we know soon enough. We are the only manufacturer of LED headlights in Australia – please consider supporting Australian businesses.

These are unbreakable. They come with a lifetime warranty and we will replace a light even if it is damaged in a collision. You cant even break them with a hammer.

They have breathers so as to avoid fogging or condensation and we have a breather kit option (just like diff breathers) for the serious off roader likely to do bonnet depth creek crossings. JTX are the preferred light chosen by the off road racing guys.

Wiring up the Day Running Lights is very easy They get their earth through the 3 pin H4 headlight socket. The red wire is to power the primary DRL colour, so wire that to the parkers or to a power source that comes on with the ignition. The yellow wire powers the secondary colour which is typically amber in which case connect to indicator or to a separate switch if you have a twin colour set up like red and white.

Specs:

• The lights have a depth of 65mm, and are 178mm in diameter.
• Headlight amp draw: 3A each.
• Halo amp draw: 0.35A each.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Braking upgrades should be done in conjunction with power increases and we have found the biggest improvement can be achieved with this mod. A PDI dual diaphragm brake booster for the 80 series is not only new but is larger and will give an increase in brake performance as the booster assist ratio is higher than factory.

Our PDI dual diaphragm brake boosters have been ADR tested and proved to pass all tests. Our design allows us to exceed the standard brake specifications for those with:

• increased weight (both GVM and GCM).

• larger wheel diameter

The only fitting issue is for those with rear air con or ice box console where the alloy pressure lines are routed close to the brake booster and will result in interference such that our larger boosters can’t be fitted.

We recommend these be installed with braided brake lines as line pressure will be increased and the standard lines may be compromised if still original. This is both due to age and the potential for damage as they are fitted to a 4WD. Installing braided lines will also give a better result as factory flexible lines bulge and reduce effective application of the pedal.

These are suited for an 80 series Landcruiser, and may be suitable for installation on both the petrol and diesel 60 Series models; we do not guarantee these will fit your 60 Series, please do your research before purchasing and attempting an install. For those fitting to petrol models we suggest and additional vacuum reservoir be added to ensure the booster is able to provide full assist for a period after the engine is turned off or if being driven enthusiastically where vacuum build up is limited.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

This kit has been meticulously reproduced and professionally printed with attention to detail. Custom colours available at additional cost, contact for more information. Our stripes are "Application Ready", easy-to-install and professionally manufactured from the highest quality Avery vinyls with clear laminate to ensure years of trouble-free use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Touge Nation Money-Back Satisfaction Guarantee!

Please note: all 60 series body stripe kits from Touge Nation are made-to-order, and kits can take up to 2-3 weeks before being dispatched for delivery.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

This kit has been meticulously reproduced and professionally printed with attention to detail. Custom colours available at additional cost, contact for more information. Our stripes are "Application Ready", easy-to-install and professionally manufactured from the highest quality Avery vinyls with clear laminate to ensure years of trouble-free use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Touge Nation Money-Back Satisfaction Guarantee!

Please note: all 60 series body stripe kits from Touge Nation are made-to-order, and kits can take up to 2-3 weeks before being dispatched for delivery.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

ONCE SOLD OUT, PRE-ORDER FOR JANUARY 2024 ARRIVAL!

The ultimate nut & bolt replacement kit for anyone restoring, repairing or upgrading their 60 series 🔥

When you pull out those 30+ year old nuts & bolts from your rig, this kit will come in handy...we promise 🙏

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and yellow and black