Siege Overland

Fresh nuts and bolts, there is nothing better! Well, almost 😎

If you have seized, rusty bolts on your 60 series (there is a 95% chance of this), then it is likely you could use this kit ✔️

There is something extremely satisfying in replacing old tired bolts with some freshly zinc plated nuts and bolts 😍

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and yellow zinc coated, to help prevent bolt shearing and save you time. This kit has saved us many times on our own 60, you won't regret this purchase.

Each Kit Contains:

• 55 - M5 Serrated Nut, 8mm Head.
• 150 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 30 - M10 Serrated Nut, 14mm Head.
• 30 - M6.3 x 19mm M10 Hex Head Self Tapper.
• 30 - M5 x 22mm Panel Bolt, 8mm Head, 18mm Washer.
• 75 - M6 x 16mm Panel Bolt M10 Head.
• 30 - M6 x 20mm Panel Bolt M10 Head with 18mm Washer.
• 30 - M6 x 25 Panel Bolt, 10mm Head
• 25 - M8 x 25mm Panel Bolt, 13mm Head
• 25 - M10 x 30mm Panel Bolt, 14mm Head

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

 Is your 60 Series still wearing it's original carpet? Chances are very likely, yes it is 👎🏽

It most likely still has dog hair in there from the previous 2x owners, Maccas chips from that late night last year along with some other 'memories embedded' in it 🍟🐶

Definitely, time to replace 🔄

Your 60 Series isn't a new car, but we know there's been a few times when you've hopped in and thought "geez I wish this interior felt cleaner, newer, fresher" 😩

*Please note that wheel arch covers are not included in the rear for this set of carpet for HJ61 and FJ62

This is the first step to a fresh interior... 👄

What problems will this solve?

• Affordable interior refreshen 🍃
• Easy enough self-install; less than half a day 🪛
• Change or refresh the faded old colour 🧼
• Choose a new loop style, or retain the original style 🤌🏽

🔧 Installation, our thoughts? 🤔

Pretty simple install, our process looked like this:

• Throw down a canvas sheet 
• Remove the front seats and centre console
• Remove the rear seats
• Pull out the carpet
• Lay the old carpet down; mark out the old holes on the back of the new carpet, only slice these holes (don't fully cut them out)
• Do sound deadening removal and replace with Car Builders wagon pack (if up to it)
• Lay in your new carpet
• Begin cutting in (very carefully) your handbrake, shifter and seat holes
• Trim off the excess sides of the new carpet (overhanging doors etc.)
• Re-install seats
• Sit back and enjoy your work 👀🍺

PLEASE NOTE: item is custom made to suit your vehicle and is non-refundable or returnable

Important details:

• 📦 This carpet is made to order; please allow 7-12 working days for your carpet to be shipped, although we aim for 3-4 working days before shipment; you accept that this will take up to 10 business days to make and send + shipping times
• 📑 Please note this carpet will suit; HJ60, HJ61, FJ60, FJ62. These really work well for HJ61s and FJ62s
• 💺 This carpet does cater to (although you will need to mark out and cut out) an under seat heater on the driver's side for HJ61's and FJ62's
• ✂️ Holes are not cut into these carpets; you will need to mark out and cut your own seat, heater, handbrake and shifter holes
• 👉🏽 Whilst these carpets are as close as can be to original; there is some age in the moulds and they may change over time, your floor pan may be slightly varied, or the carpet may take time to get to shape; please allow for this, carpets are made to order you accept all of these conditions when ordering this carpet
• Please note that wheel arch covers are NOT included with this carpet for the rear and must be ordered separately

A note from our supplier: 

Loop Pile - This carpet is constructed using top-quality spun Acrylic yarn and is tufted on a 5/32" gauge tufting machine at 600 grams per square meter.
The carpet is produced in one-meter-wide rolls which are backed with Polyethylene which enables it to be moulded to the contours of an automotive floor pan.
As its name suggests loop pile carpet is made up using many small loops of yarn and is most commonly used in vehicles from the 1960's up until the mid 1980's.

Classic Loop - Our strongest and most durable carpet material. Manufactured by us using the original 80% Rayon and 20% Nylon yarn, it is an exact reproduction of the carpet used by the car makers during 1960’s to 1970’s, including the 60 Series Landcruiser, other types that used this were HK-HG Holden, XT-XY Falcon, Valiant Charger and many other models. It is available in most original colours including black, saddle (Ford), Chev + GMH blue, VH Commodore (Brock), Burgundy along with many other colours and is suitable for all makes and models including present day vehicles.

Please note our carpet comes with NO holes cut in it. Free fitting instructions:

1 - open your parcel, make sure you have everything you ordered
2 - Lay out your new carpet and pop moulded contours back into place if applicable
3 - Remove door sill plates, kick panels, front seats and rear seat base
4 - Remove centre console (where applicable), seat belt bolts and any other trims retaining old carpet
5 - Remove old carpet, keep it do not discard it yet. Remove old underfelt taking note of where it was. Vacuum or sweep the floor clean. Place the old carpet over your new moulded carpet. Using the old carpet as a template, mark any holes or additional cut outs on the new carpet with chalk. Do not cut yet. 
6 - If removing underfelt only, lay it in the same area as you removed it from. 
7 - Starting with the rear carpet, place your new carpet in the vehicle by entering it on the tunnel and working towards the sides.
8 - Now repeat this with the front carpet matching the contours of the carpet with the floor
9 - You may need to cut some of the holes you marked out earlier (gearstick, console brackets, etc.)
10 - After confirming the proper fit, cut the required holes as you fit the carpet to the vehicle
11 - depending on your particular model of vehicle it may be necessary to trim the excess carpet from the sides as most carpets are left slightly wider in case the carpet has been fitted slightly off centre.
12 - replace rear seat base, seat belt bolts, centre console, front seat bolts, kick panels, door sill plates and any other trims your removed earlier.

Please note the colour reproduction of these samples will vary dependant on the viewers graphics/monitor settings. We advise the customer to always email team@siegeoverland.com to discuss their requirements if they have any doubts regarding the correct colour for their vehicle.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Is your carpet getting a bit old, dirty and messy? 🧹

Do you need to clean it often, just to TRY feel some cleanliness? 🧼

⏰ It could be time to replace it with some fresh carpet; moulded and made in Australia 🇦🇺, these kits are the best replacement carpet we could find for HJ60 and FJ60 Series Landcruisers!

All kits come pre-moulded, all you need to do is trim the carpet down to size ✂️

Pre-moulded front, rear and cargo car carpet for the Toyota Landcruiser  (HJ60,FJ60, 60 Series) 1980-1990 including door cards, tailgate and cargo trim!

Warning: These will not fit HJ61, or FJ62 SERIES due to under-seat heaters, shop here for HJ61 and FJ62 model carpets.

PLEASE NOTE: item is custom made to suit your vehicle and is non-refundable or returnable

These carpets even come with a heel pad on the driver's side. (though we do our best to colour code this heel pad, they default to black if colour isn't available).

Fitting instructions are included with the product, and no holes are cut in the carpet. There is an overlap between the front and rear so it can be trimmed in and adjusted to your car. This is an after-market product, though very close to the original 🕶

All of our products are made to order, so please ensure you've picked the correct model and colour that you're after.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service.

 Is your 60 Series still wearing it's original carpet? Chances are very likely, yes it is 👎🏽

It most likely still has dog hair in there from the previous 2x owners, Maccas chips from that late night last year along with some other 'memories embedded' in it 🍟🐶

Definitely, time to replace 🔄

Your 60 Series isn't a new car, but we know there's been a few times when you've hopped in and thought "geez I wish this interior felt cleaner, newer, fresher" 😩

This is the first step to a fresh interior... 👄

What problems will this solve?

• Affordable interior refreshen 🍃
• Easy enough self-install; less than half a day 🪛
• Change or refresh the faded old colour 🧼
• Choose a new loop style, or retain the original style 🤌🏽

🔧 Installation, our thoughts? 🤔

Pretty simple install, our process looked like this:

• Throw down a canvas sheet 
• Remove the front seats and centre console
• Remove the rear seats
• Pull out the carpet
• Lay the old carpet down; mark out the old holes on the back of the new carpet, only slice these holes (don't fully cut them out)
• Do sound deadening removal and replace with Car Builders wagon pack (if up to it)
• Lay in your new carpet
• Begin cutting in (very carefully) your handbrake, shifter and seat holes
• Trim off the excess sides of the new carpet (overhanging doors etc.)
• Re-install seats
• Sit back and enjoy your work 👀🍺

Important details:

• 📦 This carpet is made to order; please allow 7-12 working days for your carpet to be shipped, although we aim for 3-4 working days before shipment; you accept that this will take up to 10 business days to make and send + shipping times
• 📑 Please note this carpet will suit; HJ60, HJ61, FJ60, FJ62. These really work well for HJ61s and FJ62s
• 💺 This carpet does cater to (although you will need to mark out and cut out) an under seat heater on the driver's side for HJ61's and FJ62's
• ✂️ Holes are not cut into these carpets; you will need to mark out and cut your own seat, heater, handbrake and shifter holes
• 👉🏽 Whilst these carpets are as close as can be to original; there is some age in the moulds and they may change over time, your floor pan may be slightly varied, or the carpet may take time to get to shape; please allow for this, carpets are made to order you accept all of these conditions when ordering this carpet

PLEASE NOTE: item is custom made to suit your vehicle and is non-refundable or returnable

A note from our supplier:

Plush Pile - Uses a similar construction process to Loop pile but with a much higher yarn density of 750 grams per square meter.
Plush pile (sometimes referred to as Cut pile) gives a more luxurious appearance and is generally used in most vehicles from the mid 1980's to the present day.

Super Plush - Uses a similar construction process to plush pile but with a much higher yarn density of 950 grams per square meter. Super Plush pile gives of a lush and thick luxurious appearance. Originally Used in the early 70s for SLE commodores, Ford LTD and Statesmen.  

Please note our carpet comes with NO holes cut in it. Free fitting instructions:

1 - open your parcel, make sure you have everything you ordered
2 - Lay out your new carpet and pop moulded contours back into place if applicable
3 - Remove door sill plates, kick panels, front seats and rear seat base
4 - Remove centre console (where applicable), seat belt bolts and any other trims retaining old carpet
5 - Remove old carpet, keep it do not discard it yet. Remove old underfelt taking note of where it was. Vacuum or sweep the floor clean. Place the old carpet over your new moulded carpet. Using the old carpet as a template, mark any holes or additional cut outs on the new carpet with chalk. Do not cut yet. 
6 - If removing underfelt only, lay it in the same area as you removed it from. 
7 - Starting with the rear carpet, place your new carpet in the vehicle by entering it on the tunnel and working towards the sides.
8 - Now repeat this with the front carpet matching the contours of the carpet with the floor
9 - You may need to cut some of the holes you marked out earlier (gearstick, console brackets, etc.)
10 - After confirming the proper fit, cut the required holes as you fit the carpet to the vehicle
11 - depending on your particular model of vehicle it may be necessary to trim the excess carpet from the sides as most carpets are left slightly wider in case the carpet has been fitted slightly off centre.
12 - replace rear seat base, seat belt bolts, centre console, front seat bolts, kick panels, door sill plates and any other trims your removed earlier.

Please note: the colour reproduction of these samples will vary dependant on the viewers graphics/monitor settings. We have no control over these settings and would advise the customer to always email team@siegeoverland.com to discuss their requirements if they have any doubts regarding the correct colour for their vehicle."

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

The ultimate nut & bolt replacement kit for anyone restoring, repairing or upgrading their 60 series 🔥

When you pull out those 30+ year old nuts & bolts from your rig, this kit will come in handy...we promise 🙏

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and yellow and blackzinc coated, to help prevent bolt shearing and save you time. 

What's included? 

1 x 730 Piece Set, Yellow Zinc Coated:

• 55 - M5 Serrated Nut, 8mm Head.
• 150 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 30 - M10 Serrated Nut, 14mm Head.
• 30 - M6.3 x 19mm M10 Hex Head Self Tapper.
• 30 - M5 x 22mm Panel Bolt, 8mm Head, 18mm Washer.
• 75 - M6 x 16mm Panel Bolt M10 Head.
• 30 - M6 x 20mm Panel Bolt M10 Head with 18mm Washer.
• 30 - M6 x 25 Panel Bolt, 10mm Head
• 25 - M8 x 25mm Panel Bolt, 13mm Head
• 100 - M6 Washer
• 50 - M8 Washer
• 50 - M10 Washer
• 25 - M10 x 30mm Panel Bolt, 14mm Head

1 x 550 Piece Set, Black Zinc Coated:

• 50 - M5 Serrated Nut, 8mm Head.
• 50 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 50 - 4.8mm x 16mm Phillips Head Self Tapper Screws
• 50 - M6.3 x 19mm M10 Hex Head Self Tapper,16mm Washer.
• 30 - M5 x 19mm Panel Bolt, 8mm Head, 13mm Washer.
• 50 - M6 x 16mm Panel Bolt M10 Head.
• 25 - M6 x 18mm Panel Bolt M10 Head with 20mm Washer.
• 25 - M6 x 25 Panel Bolt, 10mm Head with 20mm Washer
• 25 - M8 x 25mm Panel Bolt, 12mm Head
• 50 - M6 Flat Washers
• 50 - M8 Flat Washers
• 50 - M10 Washer

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

We are excited to bring you under bonnet insulation to suit your 60 series landcruiser (all years). 

This product is an aftermarket item and is not an exact copy of the original TOYOTA item.

Tests show that this product absorbs more noise than most other types of pads. This is due to its multi-density construction which absorbs a larger range of noise frequencies than other single layer products.

PLEASE NOTE: Due to the size of the box, it must be sent via courier, not AusPost. We must have a street address (NOT PO Box's and parcel lockers etc.)

Installed in seconds! Fully pre-moulded & cut to size. Comes with clips to fit factory holes. No gluing or cleaning required. Under Bonnet noise/heat pads are standard equipment on all upmarket vehicles absorbing engine and road noise before it can enter the passenger cabin. Have you ever had polished floorboards in a room which has then had carpet installed? The room becomes so much quieter! Our Under-Bonnet Noise Absorption pads work on the same principle.

FIRE RETARDANT - resists absorption of oils, petrol etc. Exceeds international standards relating to under-bonnet fire safety regulations, including regulations: DIN75200, DIN54333, US-FMVSS-302

NOTE: This item is made to order, please allow between 3-4 weeks for your order to be dispatched.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service.

Say goodbye to seized, rusted nuts and bolts in your 60 series and say HELLO to...all-black zinc coated nuts and bolts to freshen up and replace those 30+ year old ones 🔥

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and black zinc coated, to help prevent bolt shearing and save you time!

Each Kit Contains:

• 50 - M5 Serrated Nut, 8mm Head.
• 50 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 50 - 4.8mm x 16mm Phillips Head Self Tapper Screws.
• 50 - M6.3 x 19mm M10 Hex Head Self Tapper, 16mm Washer.
• 25 - M5 x 19mm Panel Bolt, 8mm Head, 13mm Washer.
• 50 - M6 x 16mm Panel Bolt M10 Head.
• 25 - M6 x 18mm Panel Bolt M10 Head with 20mm Washer.
• 25 - M6 x 25 Panel Bolt, 10mm Head, 20mm Washer
• 50 - M6 Flat Washers
• 50 - M8 Flat Washers
• 25 - M8 x 25mm Panel Bolt, 12mm Head

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Size guide

Looking for the perfect gift for a 60 series owner? Give the gift of choice with a Siege Overland E-Gift Card. 

With this gift card, you can select from our full range of the best brand 60 series parts and upgrades including 3XM Canopies, PDI Intercoolers, Touge Nation, JTX Lighting and loads more. 

Starting from as little as $10, this is a no-brainer for the 60 series lover in your life!

Are you thinking it's time to upgrade those old rusty, seized nuts and bolts on your 60 series landcruiser? 

Grab this 370 piece yellow zinc coated set today to make your 60 feel (a little bit) shiny and new again 🔩

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and black zinc coated, to help prevent bolt shearing and save you time!

Each Kit Contains:

• 50 - M5 Serrated Nut M8 Head
• 80- M6 Serrated Nut M10Head
• 50 - M8 Serrated Nut M12 Head
• 25 - M10 Serrated Nut M14 Head
• 10 - M6.3 x 19mm M10 Hex Head Self Tapper
• 25 - M5 x 22mm Panel Bolt M8Head, 18mm Washer philips head
• 50 - M6 x 20mm Panel Bolt M10 Head flat and spring washer
• 25 - M6 x 20mm Panel Bolt M10 Head with 18mm Washer
• 25 - M6 x 25mm Bolt Panel M10 Head flat and spring washer
• 20 - M8 x 25mm Panel Bolt M12 Head flat and spring washer
• 10 - M10 x 30mm Panel Bolt M14 Head flat and spring washer
  

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Size guide

Size guide

Is it time to upgrade those old rusty, seized nuts and bolts on your 60 series landcruiser? 

Grab this 400 piece set today and make your 60 feel (a little bit) shiny and new again 🤙 

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and black zinc coated, to help prevent bolt shearing and save you time!

Each Kit Contains:

• 50 - M5 Serrated Nut, 8mm Head.
• 50 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 50 - 4.8mm x 16mm Phillips Head Self Tapper Screws.
• 50 - M6.3 x 19mm M10 Hex Head Self Tapper, 16mm Washer.
• 25 - M5 x 19mm Panel Bolt, 8mm Head, 13mm Washer.
• 50 - M6 x 16mm Panel Bolt M10 Head.
• 25 - M6 x 18mm Panel Bolt M10 Head with 20mm Washer.
• 25 - M6 x 25 Panel Bolt, 10mm Head, 20mm Washer
• 25 - M8 x 25mm Panel Bolt, 12mm Head

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Are you restoring or repairing your 60? Have you lost some nut and bolts along the way, or maybe you've found some seized and rusted ones...🫣

Either way, this kit will 110% come in handy, as we have found out...many times ✅

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser.

Manufactured to our High Quality & Strength Standard, all stainless steel, to help prevent Bolt Shearing and save you time. 

Each Kit Contains:

• 50 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 13mm Head.
• 50 - M6 Flat Washers
• 50 - M8 Flat Washers
• 50 - M10 Flat Washers
• 25 - M5 x 20mm Panel Bolt, 8mm Head with Flat + Spring Washer.
• 50 - M6 x 16mm Panel Bolt, 10mm Head with Flat + Spring Washer.
• 25 - M6 x 18mm Panel Bolt, 10mm Head with Flat + Spring Washer.
• 25 - M6 x 25mm Panel Bolt, 10mm Head with Flat + Spring Washer.
• 25 - M8 x 25mm Panel Bolt 13mm Head with Flat + Spring Washer
• 50 - M6 x 20mm Button Head with Flat + Spring Washer
• 25 - M8 x 16mm Counter Sunk, Phillips Head
• 25 - M8 Star Washers

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Size guide

Size guide

Size guide

We are stoked to bring you our newest (and by far our favourite) graphic t-shirt. This tee will be your new go-to, perfect for working on your 60, or adventures away!

Grab yours now, and be sure to checkout our range of stickers, jumpers and more.

• 100% combed ring-spun cotton
• Charcoal Heather and Carbon Grey is 60% cotton and 40% polyester
• Fabric weight: 6.5 oz/yd² (220 g/m²)
• 20 singles
• Regular fit
• Side-seamed construction
• 1 × 1 rib at collar
• Single-needle edge stitch 7/8″
• Blank product sourced from Bangladesh

This product is made especially for you as soon as you place an order, which is why it takes us a bit longer to deliver it to you. Making products on demand instead of in bulk helps reduce overproduction, so thank you for making thoughtful purchasing decisions!

Size guide

Are you restoring or repairing your 60? Have you lost some nut and bolts along the way, or maybe you've found some seized and rusted ones!

Either way, this kit will 110% come in handy, as we have found out...many times 🫣

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser.

Manufactured to our High Quality & Strength Standard, all stainless steel, to help prevent Bolt Shearing and save you time. 

Each Kit Contains:

• 25 - M6 Serrated Nut M10 Head.
• 25 - M8 Serrated Nut M13 Head
• 25 - M5 x 20mm Panel Bolt M10 Head spring and flat washer
• 25 - M6 x 16mm Panel Bolt M10 Head spring and flat washer
• 25 - M6 x 18mm Panel Bolt M10 Head spring and flat washer
• 25 - M6 x 25mm Panel Bolt M10 Head spring and flat washer
• 25 - M6 x 20mm Button screw
• 25 - M8 x 25mm bolt M13 Head spring and flat washer
• 25 - M8 x 10mm Countersunk screw
• 25 - M8 star washer
• 50 - M6 Flat washer
• 50 - M8 Flat washer
• 50 - M10 Flat washer
  

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Get set for winter cruising in your 60 with our latest drop in collaboration with @rove_rhususchrist & @rove_renae (aka GONE ROVE)! We have no doubt this hoodie will be your new favourite, with an epic graphic featuring Gone Rove's 60 series landcruiser.

• 50% pre-shrunk cotton, 50% polyester
• Fabric weight: 8.0 oz/yd² (271.25 g/m²)
• Air-jet spun yarn with a soft feel and reduced pilling
• Double-lined hood with matching drawcord
• Quarter-turned body to avoid crease down the middle
• 1 × 1 athletic rib-knit cuffs and waistband with spandex
• Front pouch pocket
• Double-needle stitched collar, shoulders, armholes, cuffs, and hem
• Blank product sourced from Bangladesh, Nicaragua, Honduras or El Salvador

This product is made especially for you as soon as you place an order, which is why it takes us a bit longer to deliver it to you. Making products on demand instead of in bulk helps reduce overproduction, so thank you for making thoughtful purchasing decisions!

Size guide