Afterpay Day Sale

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Ultimate style and class; the Sahara Style Flares. 

NOTE: flares are now available for pre-order, order now for delivery in FEB 2025.

Sahara’s traditionally came with fibreglass flares; they gave them a stronger, thicker and even ‘stauncher’ look 😤

It’s hard to track down a good set, some that fits, bolts up and is new and free of damage.

Well, Mick at FRP flares was asked to help a few mates replace their cracked Sahara flares and he came up with these Sahara style flares for those who were after the awesome look 👀😍

FRP Flares, are the BEST aftermarket flares available for 60 Series Landcruisers.

These flares come as a full set, and are supplied in a black or white gelcoat finish, allowing you to paint them to match or contrast your current paintwork 🎨

FRP recommend priming and painting for a good quality and uv resistant finish.  

They're easy to paint and there's no special treatment required, simply sand, prime, sand and paint as you would any panel on the vehicle ✅

Due to the age of the moulds some refinishing may be required, but not much at all 👌🏽

When installing, the top edge of the flares get covered by the rubber seals, underside is a hollow fibreglass.

As you can see in the photos these flares finish at the bottom of the guards so no need for genuine mudflaps.  

FRP flares are screwed to the underlip of the guards, allowing the most cost effective and more importantly the strongest fit possible unlike double sided tape, avoiding fragile and intrusive fitment.

Screws not  included – as a guide 8 gauge 20mm self-drilling button heads, may be most appropriate.

Door flares are supplied with a fibreglass bracket which is screwed to the door then the door flare is screwed to the bracket, this means your flares will never fall off. 

PLEASE NOTE: FRP's OEM Replacement Flares may not bolt directly into existing holes due to manufacturing variations between vehicles.This product is made to order and is NON-RETURNABLE and NON-REFUNDABLE

Some things to know before purchasing:

• FRP state that these DO NOT replace genuine Sahara flares but act as an alternative 🤙🏽
• These flares should be installed by a professional 👨🏽‍🔧
• Shipping is expensive, we apologise! We are trying to find a more economical option but come up short, due to the size of these. If you want to pick these up from Brisbane, Australia please let us know. This is possible 📦
• Although it is possible to install them yourself; we will not warrant, guarantee or grant the return any fibreglass, FRP or Flares products that are installed incorrectly and/or not installed by a professional 🚫
• When purchasing these flares you accept all of these conditions, as well as our terms of service, found below.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Fresh nuts and bolts, there is nothing better! Well, almost 😎

If you have seized, rusty bolts on your 60 series (there is a 95% chance of this), then it is likely you could use this kit ✔️

There is something extremely satisfying in replacing old tired bolts with some freshly zinc plated nuts and bolts 😍

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and yellow zinc coated, to help prevent bolt shearing and save you time. This kit has saved us many times on our own 60, you won't regret this purchase.

Each Kit Contains:

• 55 - M5 Serrated Nut, 8mm Head.
• 150 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 30 - M10 Serrated Nut, 14mm Head.
• 30 - M6.3 x 19mm M10 Hex Head Self Tapper.
• 30 - M5 x 22mm Panel Bolt, 8mm Head, 18mm Washer.
• 75 - M6 x 16mm Panel Bolt M10 Head.
• 30 - M6 x 20mm Panel Bolt M10 Head with 18mm Washer.
• 30 - M6 x 25 Panel Bolt, 10mm Head
• 25 - M8 x 25mm Panel Bolt, 13mm Head
• 25 - M10 x 30mm Panel Bolt, 14mm Head

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

 Is your 60 Series still wearing it's original carpet? Chances are very likely, yes it is 👎🏽

It most likely still has dog hair in there from the previous 2x owners, Maccas chips from that late night last year along with some other 'memories embedded' in it 🍟🐶

Definitely, time to replace 🔄

Your 60 Series isn't a new car, but we know there's been a few times when you've hopped in and thought "geez I wish this interior felt cleaner, newer, fresher" 😩

*Please note that wheel arch covers are not included in the rear for this set of carpet for HJ61 and FJ62

This is the first step to a fresh interior... 👄

What problems will this solve?

• Affordable interior refreshen 🍃
• Easy enough self-install; less than half a day 🪛
• Change or refresh the faded old colour 🧼
• Choose a new loop style, or retain the original style 🤌🏽

🔧 Installation, our thoughts? 🤔

Pretty simple install, our process looked like this:

• Throw down a canvas sheet 
• Remove the front seats and centre console
• Remove the rear seats
• Pull out the carpet
• Lay the old carpet down; mark out the old holes on the back of the new carpet, only slice these holes (don't fully cut them out)
• Do sound deadening removal and replace with Car Builders wagon pack (if up to it)
• Lay in your new carpet
• Begin cutting in (very carefully) your handbrake, shifter and seat holes
• Trim off the excess sides of the new carpet (overhanging doors etc.)
• Re-install seats
• Sit back and enjoy your work 👀🍺

PLEASE NOTE: item is custom made to suit your vehicle and is non-refundable or returnable

Important details:

• 📦 This carpet is made to order; please allow 7-12 working days for your carpet to be shipped, although we aim for 3-4 working days before shipment; you accept that this will take up to 10 business days to make and send + shipping times
• 📑 Please note this carpet will suit; HJ60, HJ61, FJ60, FJ62. These really work well for HJ61s and FJ62s
• 💺 This carpet does cater to (although you will need to mark out and cut out) an under seat heater on the driver's side for HJ61's and FJ62's
• ✂️ Holes are not cut into these carpets; you will need to mark out and cut your own seat, heater, handbrake and shifter holes
• 👉🏽 Whilst these carpets are as close as can be to original; there is some age in the moulds and they may change over time, your floor pan may be slightly varied, or the carpet may take time to get to shape; please allow for this, carpets are made to order you accept all of these conditions when ordering this carpet
• Please note that wheel arch covers are NOT included with this carpet for the rear and must be ordered separately

A note from our supplier: 

Loop Pile - This carpet is constructed using top-quality spun Acrylic yarn and is tufted on a 5/32" gauge tufting machine at 600 grams per square meter.
The carpet is produced in one-meter-wide rolls which are backed with Polyethylene which enables it to be moulded to the contours of an automotive floor pan.
As its name suggests loop pile carpet is made up using many small loops of yarn and is most commonly used in vehicles from the 1960's up until the mid 1980's.

Classic Loop - Our strongest and most durable carpet material. Manufactured by us using the original 80% Rayon and 20% Nylon yarn, it is an exact reproduction of the carpet used by the car makers during 1960’s to 1970’s, including the 60 Series Landcruiser, other types that used this were HK-HG Holden, XT-XY Falcon, Valiant Charger and many other models. It is available in most original colours including black, saddle (Ford), Chev + GMH blue, VH Commodore (Brock), Burgundy along with many other colours and is suitable for all makes and models including present day vehicles.

Please note our carpet comes with NO holes cut in it. Free fitting instructions:

1 - open your parcel, make sure you have everything you ordered
2 - Lay out your new carpet and pop moulded contours back into place if applicable
3 - Remove door sill plates, kick panels, front seats and rear seat base
4 - Remove centre console (where applicable), seat belt bolts and any other trims retaining old carpet
5 - Remove old carpet, keep it do not discard it yet. Remove old underfelt taking note of where it was. Vacuum or sweep the floor clean. Place the old carpet over your new moulded carpet. Using the old carpet as a template, mark any holes or additional cut outs on the new carpet with chalk. Do not cut yet. 
6 - If removing underfelt only, lay it in the same area as you removed it from. 
7 - Starting with the rear carpet, place your new carpet in the vehicle by entering it on the tunnel and working towards the sides.
8 - Now repeat this with the front carpet matching the contours of the carpet with the floor
9 - You may need to cut some of the holes you marked out earlier (gearstick, console brackets, etc.)
10 - After confirming the proper fit, cut the required holes as you fit the carpet to the vehicle
11 - depending on your particular model of vehicle it may be necessary to trim the excess carpet from the sides as most carpets are left slightly wider in case the carpet has been fitted slightly off centre.
12 - replace rear seat base, seat belt bolts, centre console, front seat bolts, kick panels, door sill plates and any other trims your removed earlier.

Please note the colour reproduction of these samples will vary dependant on the viewers graphics/monitor settings. We advise the customer to always email team@siegeoverland.com to discuss their requirements if they have any doubts regarding the correct colour for their vehicle.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Welcome to performance 👑

For years we searched for an intercooler that worked with our HJ61 / 12HT; we wanted something that fit, something of high quality and finally something that was large enough to make a difference on EGT's and IAT's.

We, like you, wanted:

• 💨 Performance
• ⚡️ Quality
• 🔩 Fitment
• 👌🏽 Reliability
• 📞 Manufacturer support

Then, we came across the PDI intercooler from Brian at Performance Diesel Intercoolers in W.A, Australia 🇦🇺

After speaking with Brian, understanding the size of this intercooler, and its design to enable fitment into the HJ61 Landcruiser, as well as it's specs and quality we knew we had to have it 🎁

Not only that, it looked bass ass 😎

If you've got a 12HT or a 2HT, usually you're keen for a little more power, more torque and better performance. 💪🏽

How do we achieve that with these old but brilliant motors? Simple; boost and fuel, > BUT this means higher EGT's and thus higher IAT's; which means hotter engine, rings going bad, overheating, head warping etc etc. 🔥😢

If you have gone through the trauma of any of the above on your beloved 12HT/2H motor then you're understanding how important it is to AVOID this at all costs 👎🏽

Because this means: 

• Getting the engine built; but then there's the cost, what if the builder isn't good and/or make an error, what about their warranty, what if the build cost blows out 💸
• Building the engine yourself; means needing to find space (mum's garage may not fit a small truck engine), finding the time; will it be one of the 50% complete projects for 3 years? you're thinking : "I hate those, my 60 is already one of those!" ⏳

If you're wanting more power, then this is for you; it means boost, cooler EGT's and lower IAT's, it means peace of mind 😌 and motivates you to get your diesel tuned (properly on a dyno 🙄), it means better trips and it looks mean 😈

* Please note, if utilising a custom set-up piping may not fit your set-up. Please let us know your requirements the closest possible will be supplied. This kit is for a 12HT set-up only, whilst we do our best to accomodate a 2H custom set-up, the responsibility of fitment it up to the customer.  

From PDI:

The PDI Landcruiser 60 series HJ61 HJ60 Front mount intercooler is designed to fit on both the round headlight and the twin square light model. It sits further back than all other designs we have seen as it has recessed areas in the end tanks for the condenser fittings and piping.

The core is 545 x 300 x 65mm.

Pipes are stainless steel and is supplied with a stainless flange onto the intake manifold, which does a 180deg bend under the air supply pipe.

Plus, it looks awesome!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Reproduction Turbo decal to suit 60-Series Land Cruiser fitted to upper tailgate, both designed and sized based off an OEM sample as well as tested on an original vehicle to ensure correct fitment, this decal is guaranteed to be correct. Printed and 2000-Series Avery vinyl and clear over-laminated for years of trouble-free use.

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Money-Back Satisfaction Guarantee!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

 Is your 60 Series still wearing it's original carpet? Chances are very likely, yes it is 👎🏽

It most likely still has dog hair in there from the previous 2x owners, Maccas chips from that late night last year along with some other 'memories embedded' in it 🍟🐶

Definitely, time to replace 🔄

Your 60 Series isn't a new car, but we know there's been a few times when you've hopped in and thought "geez I wish this interior felt cleaner, newer, fresher" 😩

This is the first step to a fresh interior... 👄

What problems will this solve?

• Affordable interior refreshen 🍃
• Easy enough self-install; less than half a day 🪛
• Change or refresh the faded old colour 🧼
• Choose a new loop style, or retain the original style 🤌🏽

🔧 Installation, our thoughts? 🤔

Pretty simple install, our process looked like this:

• Throw down a canvas sheet 
• Remove the front seats and centre console
• Remove the rear seats
• Pull out the carpet
• Lay the old carpet down; mark out the old holes on the back of the new carpet, only slice these holes (don't fully cut them out)
• Do sound deadening removal and replace with Car Builders wagon pack (if up to it)
• Lay in your new carpet
• Begin cutting in (very carefully) your handbrake, shifter and seat holes
• Trim off the excess sides of the new carpet (overhanging doors etc.)
• Re-install seats
• Sit back and enjoy your work 👀🍺

Important details:

• 📦 This carpet is made to order; please allow 7-12 working days for your carpet to be shipped, although we aim for 3-4 working days before shipment; you accept that this will take up to 10 business days to make and send + shipping times
• 📑 Please note this carpet will suit; HJ60, HJ61, FJ60, FJ62. These really work well for HJ61s and FJ62s
• 💺 This carpet does cater to (although you will need to mark out and cut out) an under seat heater on the driver's side for HJ61's and FJ62's
• ✂️ Holes are not cut into these carpets; you will need to mark out and cut your own seat, heater, handbrake and shifter holes
• 👉🏽 Whilst these carpets are as close as can be to original; there is some age in the moulds and they may change over time, your floor pan may be slightly varied, or the carpet may take time to get to shape; please allow for this, carpets are made to order you accept all of these conditions when ordering this carpet

PLEASE NOTE: item is custom made to suit your vehicle and is non-refundable or returnable

A note from our supplier:

Plush Pile - Uses a similar construction process to Loop pile but with a much higher yarn density of 750 grams per square meter.
Plush pile (sometimes referred to as Cut pile) gives a more luxurious appearance and is generally used in most vehicles from the mid 1980's to the present day.

Super Plush - Uses a similar construction process to plush pile but with a much higher yarn density of 950 grams per square meter. Super Plush pile gives of a lush and thick luxurious appearance. Originally Used in the early 70s for SLE commodores, Ford LTD and Statesmen.  

Please note our carpet comes with NO holes cut in it. Free fitting instructions:

1 - open your parcel, make sure you have everything you ordered
2 - Lay out your new carpet and pop moulded contours back into place if applicable
3 - Remove door sill plates, kick panels, front seats and rear seat base
4 - Remove centre console (where applicable), seat belt bolts and any other trims retaining old carpet
5 - Remove old carpet, keep it do not discard it yet. Remove old underfelt taking note of where it was. Vacuum or sweep the floor clean. Place the old carpet over your new moulded carpet. Using the old carpet as a template, mark any holes or additional cut outs on the new carpet with chalk. Do not cut yet. 
6 - If removing underfelt only, lay it in the same area as you removed it from. 
7 - Starting with the rear carpet, place your new carpet in the vehicle by entering it on the tunnel and working towards the sides.
8 - Now repeat this with the front carpet matching the contours of the carpet with the floor
9 - You may need to cut some of the holes you marked out earlier (gearstick, console brackets, etc.)
10 - After confirming the proper fit, cut the required holes as you fit the carpet to the vehicle
11 - depending on your particular model of vehicle it may be necessary to trim the excess carpet from the sides as most carpets are left slightly wider in case the carpet has been fitted slightly off centre.
12 - replace rear seat base, seat belt bolts, centre console, front seat bolts, kick panels, door sill plates and any other trims your removed earlier.

Please note: the colour reproduction of these samples will vary dependant on the viewers graphics/monitor settings. We have no control over these settings and would advise the customer to always email team@siegeoverland.com to discuss their requirements if they have any doubts regarding the correct colour for their vehicle."

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

Is your carpet getting a bit old, dirty and messy? 🧹

Do you need to clean it often, just to TRY feel some cleanliness? 🧼

⏰ It could be time to replace it with some fresh carpet; moulded and made in Australia 🇦🇺, these kits are the best replacement carpet we could find for HJ60 and FJ60 Series Landcruisers!

All kits come pre-moulded, all you need to do is trim the carpet down to size ✂️

Pre-moulded front, rear and cargo car carpet for the Toyota Landcruiser  (HJ60,FJ60, 60 Series) 1980-1990 including door cards, tailgate and cargo trim!

Warning: These will not fit HJ61, or FJ62 SERIES due to under-seat heaters, shop here for HJ61 and FJ62 model carpets.

PLEASE NOTE: item is custom made to suit your vehicle and is non-refundable or returnable

These carpets even come with a heel pad on the driver's side. (though we do our best to colour code this heel pad, they default to black if colour isn't available).

Fitting instructions are included with the product, and no holes are cut in the carpet. There is an overlap between the front and rear so it can be trimmed in and adjusted to your car. This is an after-market product, though very close to the original 🕶

All of our products are made to order, so please ensure you've picked the correct model and colour that you're after.

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service.

Reproduction Direct Injection Turbo decal to suit 60-Series Land Cruiser fitted to tailgate, both designed and sized based off an OEM sample as well as tested on an original vehicle to ensure correct fitment, this decal is guaranteed to be correct. Printed and 2000-Series Avery vinyl and clear over-laminated for years of trouble-free use.

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Money-Back Satisfaction Guarantee!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

NOTE: currently only available for RHD model, product is made-to-order please allow up to 4-6 weeks before your order is dispatched.

Looking to protect your 60 series carpet from all the sand, dirt and everything in between that gets into your 60?

This set of Sandgrabba mats are the ultimate solution, moulded to suit your 3/4 Bench Seat 60 series setup!

Product images are for reference only, all mats are manufactured to suit vehicle.

The Sandgrabba floor mat system is moulded in a quality Poly/Rubber TPE compound precisely to the shape of the vehicle floor. The unique ridge design catches sand, mud, dirt and liquid spillages to protect the car carpet or vinyl.

• Unique ridge design catches all of the muck
• Quick-release side sill fastening system allows for easy removal
• Durable & flexible PVC / Rubber TPE construction
• Non-skid foam backing stops movement and is gentle on carpet and vinyl
• Available in Black, Grey or Beige for most cars, commercials, 4wd's and Suv's
• Sandgrabba Mat colours are based on the original Manufacturers interior colours
•  No need to make holes in your original flooring creating another inlet for sand to get into your 4x4
• Sandgrabba Mats are Proudly Australian Made and Owned

These are our famous 7 Inch LED Headlights, featuring impressive range, good spread, colourful halos and are indestructible. These draw less power than your regular halogen / HID globes too, and are ADR compliant, meaning they’re legal in every state. This is one pair of lights.

These lights come with a pair of CANBUS Load Modules to make the lights compatible with your Toyota.

These are 7″ round headlights and they fit all 7″ round applications. We have sold thousands and we are yet to have a car with 7″ lights they don’t fit. They are to suit Australian left side of road and are legal in all states. In fact they have ADR cert stamped on the lens and come with an ADR reference sheet.

JTX LED lights are made by us here in Melbourne. We carry all the components to make up all colour combinations. We make them up and send next day or even same day if we know soon enough. We are the only manufacturer of LED headlights in Australia – please consider supporting Australian businesses.

These are unbreakable. They come with a lifetime warranty and we will replace a light even if it is damaged in a collision. You cant even break them with a hammer.

They have breathers so as to avoid fogging or condensation and we have a breather kit option (just like diff breathers) for the serious off roader likely to do bonnet depth creek crossings. JTX are the preferred light chosen by the off road racing guys.

Wiring up the Day Running Lights is very easy They get their earth through the 3 pin H4 headlight socket. The red wire is to power the primary DRL colour, so wire that to the parkers or to a power source that comes on with the ignition. The yellow wire powers the secondary colour which is typically amber in which case connect to indicator or to a separate switch if you have a twin colour set up like red and white.

Specs:

• The lights have a depth of 65mm, and are 178mm in diameter.
• Headlight amp draw: 3A each.
• Halo amp draw: 0.35A each.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

The ultimate nut & bolt replacement kit for anyone restoring, repairing or upgrading their 60 series 🔥

When you pull out those 30+ year old nuts & bolts from your rig, this kit will come in handy...we promise 🙏

This nut and bolt kit is specifically designed for any pre-1990 Landcruiser. 

Manufactured to our high quality & strength standard, and yellow and blackzinc coated, to help prevent bolt shearing and save you time. 

What's included? 

1 x 730 Piece Set, Yellow Zinc Coated:

• 55 - M5 Serrated Nut, 8mm Head.
• 150 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 30 - M10 Serrated Nut, 14mm Head.
• 30 - M6.3 x 19mm M10 Hex Head Self Tapper.
• 30 - M5 x 22mm Panel Bolt, 8mm Head, 18mm Washer.
• 75 - M6 x 16mm Panel Bolt M10 Head.
• 30 - M6 x 20mm Panel Bolt M10 Head with 18mm Washer.
• 30 - M6 x 25 Panel Bolt, 10mm Head
• 25 - M8 x 25mm Panel Bolt, 13mm Head
• 100 - M6 Washer
• 50 - M8 Washer
• 50 - M10 Washer
• 25 - M10 x 30mm Panel Bolt, 14mm Head

1 x 550 Piece Set, Black Zinc Coated:

• 50 - M5 Serrated Nut, 8mm Head.
• 50 - M6 Serrated Nut, 10mm Head.
• 50 - M8 Serrated Nut, 12mm Head.
• 50 - 4.8mm x 16mm Phillips Head Self Tapper Screws
• 50 - M6.3 x 19mm M10 Hex Head Self Tapper,16mm Washer.
• 30 - M5 x 19mm Panel Bolt, 8mm Head, 13mm Washer.
• 50 - M6 x 16mm Panel Bolt M10 Head.
• 25 - M6 x 18mm Panel Bolt M10 Head with 20mm Washer.
• 25 - M6 x 25 Panel Bolt, 10mm Head with 20mm Washer
• 25 - M8 x 25mm Panel Bolt, 12mm Head
• 50 - M6 Flat Washers
• 50 - M8 Flat Washers
• 50 - M10 Washer

Sent via Auspost, these often arrive within 4–8 days of ordering 😁

For more information, please refer to our Terms of Service. By purchasing from our site you acknowledge that you have read and agree to our Terms of Service. 

NOTE: currently only available for RHD model, product is made-to-order please allow up to 4-6 weeks before your order is dispatched.

Looking to protect your 60 series carpet from all the mud, rubbish and everything in between that sneaks into your rig?

This set of Sandgrabba mats are the perfect solution, moulded to suit your individual bucket seat 60 series setup!

NOTE: currently only available for RHD model, product is made-to-order please allow up to 3-4 weeks before your order is dispatched.

Product images are for reference only, all mats are manufactured to suit vehicle.

The Sandgrabba floor mat system is moulded in a quality Poly/Rubber TPE compound precisely to the shape of the vehicle floor. The unique ridge design catches sand, mud, dirt and liquid spillages to protect the car carpet or vinyl.

• Unique ridge design catches all of the muck
• Quick-release side sill fastening system allows for easy removal
• Durable & flexible PVC / Rubber TPE construction
• Non-skid foam backing stops movement and is gentle on carpet and vinyl
• Available in Black, Grey or Beige for most cars, commercials, 4wd's and Suv's
• Sandgrabba Mat colours are based on the original Manufacturers interior colours
•  No need to make holes in your original flooring creating another inlet for sand to get into your 4x4
• Sandgrabba Mats are Proudly Australian Made and Owned

Reproduction 74552-60173 Tyre Placard decal to suit 60-Series Land Cruiser, this decal has been meticulously reproduced based off an OEM sample and sized correctly on an original vehicle.. Printed and 2000-Series Avery vinyl and clear over-laminated for years of trouble-free use.

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Money-Back Satisfaction Guarantee!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Direct reproduction plate depicting the engine details of Toyota 2H model motors. Meticulously reproduced off an OEM sample with a state-of-the-art printing system. Printed on premium vinyl and over-laminated to ensure years of trouble-free service.

Printed on .8mm semi-rigid aluminium shim stock and clear over-laminated for years of trouble-free use.

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Money-Back Satisfaction Guarantee!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Direct reproduction decal depicting "DIESEL" as found on Toyota Land Cruiser 60 Series. Meticulously reproduced off an OEM sample with a state-of-the-art printing system. Printed on premium vinyl and over-laminated to ensure years of trouble-free service.

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Money-Back Satisfaction Guarantee!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

The PDI brake booster is a significant upgrade (50%) to the 60 series, which had a single diaphragm unit. It will fit on auto models and manual with the standard clutch master cylinder, but not if you have the vacuum assist on the clutch master cylinder (due to interference).

If you have the vac assisted clutch booster, you can change it out for a non assisted clutch master, but this will require cutting and re-flaring of the hydraulic line for the clutch. Considering the improvements in clutch design, a new clutch will probably negate the need for vacuum assist and this will allow for the PDI brake booster to be installed.

Braking upgrades should be done in conjunction with power increases and we have found the biggest improvement can be achieved with this mod.

Our PDI dual diaphragm brake boosters have been ADR tested and proved to pass all tests. Our design allows us to exceed the standard brake specifications for those with:

• increased weight (both GVM and GCM).

• larger wheel diameter

Following installation and adjustment of the rear brake bias the braking distance at 80kph dropped from 26m to 16m. Very quickly we found we could do turning and stopping maneuvers that would have be both crazy and impossible before. This is great for a powered up cruiser and potentially life saving if you have increased your weights, fitted larger tyres or are towing. Many will say “the brakes are fine” but when asked if the pedal goes hard, before full braking can be achieved, they remember how scary that can be.

With a PDI brake booster less than 50kg push would be required for full braking - this is a significant improvement that will be noticed.

We recommend these be installed with braided brake lines as line pressure will be increased and the standard lines may be compromised if still original. This is both due to age and the potential for damage as they are fitted to a 4WD. Installing braided lines will also give a better result as factory flexible lines bulge and reduce effective application of the pedal.

Note: If you have air in your system, which can be very very difficult to bleed out, the larger booster will make this more apparent, due to extra force that can be applied.

These boosters are impressive, and we are sure every cruiser owner would install after driving a cruiser fitted with one of these boosters.

We recommend these be installed with braided brake lines as line pressure will be increased and the standard lines may be compromised if still original. This is both due to age and the potential for damage as they are fitted to a 4WD. Installing braided lines will also give a better result as factory flexible lines bulge and reduce effective application of the pedal.

-

The only fitting issue is for those with rear air con or ice box console where the alloy pressure lines are routed close to the brake booster and will result in interference such that our larger boosters can’t be fitted.

Please do your research before purchasing and attempting an install. For those fitting to petrol models we suggest and additional vacuum reservoir be added to ensure the booster is able to provide full assist for a period after the engine is turned off or if being driven enthusiastically where vacuum build up is limited.

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service. 

Reproduction Turbocharger Cool-Down Caution decal to suit 60-Series Land Cruiser, this decal has been meticulously reproduced based off an OEM sample and sized correctly on an original vehicle.. Printed and 2000-Series Avery vinyl and clear over-laminated for years of trouble-free use.

All TOUGE NATION decals are professionally printed on high quality Avery Dennison exterior vinyls for the ultimate in long-term use.

• Waterproof, UV Stable and Scratch Resistant
• Printed High-Quality Avery Vinyl (7 Year Guarantee)
• Ideal Indoor or Outdoor Use
• Made 100% In Australia
• Money-Back Satisfaction Guarantee!

For more information, please refer to our Terms of Service. By purchasing off our site you acknowledge that you have read and agree to our Terms of Service.